- #SET INTENSITY NICEHASH ZCASH MINER HOW TO#
- #SET INTENSITY NICEHASH ZCASH MINER SOFTWARE#
- #SET INTENSITY NICEHASH ZCASH MINER WINDOWS 7#
For AMD mining any AMD GPU with OpenCL support. 
For CPU mining a modern CPU with SSE2 support. #SET INTENSITY NICEHASH ZCASH MINER WINDOWS 7#
Windows 7 or newer operating system 64-bit. Display current rate and your balance in real time. Watch-feature - automatically restart miner if crashed or hanged. Run it only once before you start mining and after every hardware/driver/software upgrade. Integrated support for Simple Multi-Algorithm. Easy one-click GPU mining for AMD GPUs using any AMD GPU devices that supports OpenCL. Easy one-click GPU mining for NVIDIA GPUs using microarchitecture (compute capability) SM 3.0+. Easy one-click CPU mining for CPUs that support at least SSE2 (only works on Windows 圆4). Auto-tuning for best performance and efficiency, automatic selection and runtime automatic switching to most profitable cryptocurrency algorithm are all integrated into NiceHash Miner and will enable you seamless, joyful and profitable mining experience. #SET INTENSITY NICEHASH ZCASH MINER SOFTWARE#
No need to go through tons of configuration files, various mining software versions, configuration tuning or cryptocurrency coins market analysis. NiceHash Miner is an advanced auto-miner that supports the latest algorithms and miners. Please follow us on Twitter or on or Blog for updates on new versions and other important information. Please check out quick guide about NiceHash Miner, so that your experience will be even better. This version is intended for beginners or experienced miners that want the quickest updates and highest hashrates, and are okay with customization of the antivirus. NiceHash Miner is a continuation of NiceHash Miner Legacy.
#SET INTENSITY NICEHASH ZCASH MINER HOW TO#
How to run NiceHash Miner only when profitability is high enough?. Also, when some cards are weird about a setting and require an odd setting this comes in handy. When you have multiple GPUs, you can specify settings for each one by using commas inside the conf file. It should look like this: CONFIGURING MULTIPLE GPUs in the. If not, go fix it until you have valid JSON or else the miner will not start. When you’re done, use Control-X then Y and Enter to save changes, and then it will tell you that it’s Valid JSON. I believe you want around xintensity 768 for the RX480, and xintensity 368 for R9 360 cards, for example. Again, watch your commas!!! But it’s okay, because PiMP will tell you if you make a syntax error on the JSON confs.Īlso, you will want to tune your intensity values for Ethereum depending on your GPUs. Also, you will see as the second example pool, ethermine, which takes an eth Wallet address “DOT” workername as the username and “x” as the password. Usually it is good to have at least 2 pools setup in case one fails while mining, it will go to the backup pool. You can replace this with your pool/username/worker, or delete it and just use one pool, whatever you like. You will see in a lot of our confs that we use as the pool. In the case of, there are a few example pools included with PiMP. You will see a pool, wallet, username and password. This is in JSON Syntax and so the commas, quotation marks, brackets and braces are all important and you have to be careful. 
In this conf, it will look a little bit different than the. conf file example we will edit the conf for sgminer-eth. Where it says FLAGS= you can change it, to say, FLAGS=-i 4 and that would pass that along to the miner. For example, if you wanted to specify intensity for optiminer in zcash-opti.pcfg you would: edit zcash-opti.pcfg and scroll down to the bottom. We also have a place there where you can put additional command line options called FLAGS= to put them in. pcfg has a special place for the pools, users, and passwords to connect. Simply make sure that the config options that you want do not have the COMMENT OUT (IGNORE) character “#” in front of them, and that all the rest of the pools are commented out with “#”. Then you can see an example for NiceHash, which takes a BTC address “DOT” workername as its username and “x” as the password. There is flypool which takes a Zcash Wallet t-address “DOT” workername as the username and “x” as the password. In the case of opti, there are a few example pools included with PiMP. You will see a lot of text, maybe the PiMP header at the top, and then you will see a pool, wallet, username and password. If the conf you want to edit is currently mining/running, PiMP edit will warn you that the miner is running. So, in this example we will edit the conf for optiminer-zcash.
0 kommentar(er)
